killopartners.blogg.se - Web viewer for samsung dvr blank page

WEB VIEWER FOR SAMSUNG DVR BLANK PAGE HOW TO
WEB VIEWER FOR SAMSUNG DVR BLANK PAGE MANUAL
WEB VIEWER FOR SAMSUNG DVR BLANK PAGE PATCH
WEB VIEWER FOR SAMSUNG DVR BLANK PAGE PASSWORD

I followed your instructions step by step and as far as I can tell I did everything right, the internet adresses of both routers are the same now (108.216.181.97) shows on both. So to answer your question I have a bunch of stuff on my 2wire network all which works fine at the moment. If you have a static IP package from AT&T, you should be able to access your system without using Samsung's for your input. You should now be able to access your camera/DVR system while at home by wirelessly connecting to the 1200's network, and you should be able to access it while away from home by using the Samsung site's iPolis (DDNS) software. Plug in (or wirelessly connect) your camera/DVR system to the 1200.The Internet address on the 1200 should now be the same as the Internet address on the 3801.Now plug your laptop into the 3801 and access the Firewall/DMZ page and set the 1200 to DMZ and save the settings.The Internet address on the 1200 should now be in the 192.168.1.* range.Plug the ethernet cable from the 3801 into the Internet or WAN port on the 1200.

WEB VIEWER FOR SAMSUNG DVR BLANK PAGE PASSWORD

Set up the wireless on the 1200: change password and SSID, set security to WPA2/AES, turn off WPS, turn off SSID broadcast.Set the internal address of the 1200 to 192.168.2.1.

Set the 1200's Internet or WAN interface to use DHCP or Dynamic.

Plug your laptop into the 1200 and do a factory reset on it.

Remove any port mapping changes you did to the 3801 for the camera/DVR system and then reboot (power cycle) the 3801.

If everything else on your network is working fine on the 3801, you could isolate your camera/DVR system on the 1200. More than likely you will need to use the 1200 to get this to work. What other devices do you use on your network (smart phones, smart TVs, game consoles, computers, etc)? What other services do you have besides Internet (TV, VOIP)? Which port on the 1200 are you connecting the cable from 3801 to (WAN or LAN)?

Hi Jack, Let's see if we can't figure out your problem. I really dont want to spend 1/2 a day on the phone with some dude asking me if i tried turning it on and off again. I did log into the 2wire and add an application in the firwall using port settings given to me by the DVR (4520-4524) and apllied it to the linksys router on the list and still no go. One I go up stream and plug into the 2wire that IP adress is not valid (web page unknown)

WEB VIEWER FOR SAMSUNG DVR BLANK PAGE MANUAL

I then (as per the samsung manual suggests) opened up my browser, typed that IP in and was directed to the ipolis web veiwer which I was able to log on to and see all 4 cameras in action. if I have the DVR plugged strait to the 2wire it says un able to find router. I plugged my laptop into the linksys and logged into the router found the DVR connection and noted its IP adress (192.168.1.34) configerd this way thr DVR gives me a sucessfull connection status.

WEB VIEWER FOR SAMSUNG DVR BLANK PAGE PATCH

I ran a network cable from my 2wire (model3801hgv) to a secondary router (linksys modelE1200) than a patch cable from the linksys to the DVR. I did some research once I installed it and it didnt work and found a thread somwhere that said the 2wire router I am using doesnot allow uPNP which is neciarry to make my system work right, so here is how I have it set up right now. My problem is getting it to function correctly via samsungs web based system ipolis. I bought a "plug and play" dvr/camera system from samsung.

WEB VIEWER FOR SAMSUNG DVR BLANK PAGE HOW TO

Ok I am not a networking tech by any means but I know how to follow directions and i have done that till I cant go any more and my stuff still doesnt work so here I am.